|
|
Lights
Bulb holder, Bakelite, NOS, for headlight that require bulbs with 2 side pins, 2 wire.
|
Bulb holder, Bakelite, NOS, for headlight that require bulbs with 2 side pins, 3 wire.
|
Bulb holder, Bakelite, NOS, for headlight that require bulbs with 2 side pins, 4 wire.
|
Bulb, banana shaped bulb for engine compartment lights that function without a lens. These are 20 watt bulbs.
|
Bulb, headlight, NOS, H4 style, 3 spade terminals on base, 100/80 watt, relay required in system for extra wattage
|
Bulb, headlight, round globe style, 45mm diameter metal base functions as bulb holder, clear, 45/40w. Fits Carello headlights.
|
Bulb, headlight, with Bakelite bulb holder, specify bulb holder with or without parking light capability, a combination of L0240X and L0036X
|
Headlight adaptor, NOS, Carello, 6 long pigtail made of 3 wires with bullet connectors at one end and 3 prong Bakelite connectors at other end, for fitting to a more modern headlamp bulb with 3 spade terminals.
|
Headlight assembly, NOS, Carello, 00.508.700 on lens, early 50s style with vertical ribs. Valid for cars up through 1957.
|
Headlight assembly, NOS, Carello, H1 bulb style with bulb shield, #03.480.700 on lens,2 bracket & hook mount. w/o parking lamp.
|
Headlight bezels, large headlight, new manufacture, Carello script
|
Headlight bezels, large headlight, NOS, no script
|
Headlight bucket grommet plug, for attaching wires to bucket, original was white rubber, this one is black.
|
Headlight bucket, NOS, Carello, with out hold-in ring, style with screw-hole at bottom of bucket.
|
Headlight buckets, NOS, Carello, with headlamp hold-in ring and wiring
|
Headlight hold in rings, holds original European style headlights or American style sealed beams into bucket, NOS, Carello, for 170mm/7 size
|
Interior light, Quonset-hut shaped plastic lens approximately. 95mm x 22mm, set in a chromed, mostly rectangular base that is 118mm x 35mm, with rounded ends, no switch. 85.3mm between mounting screw holes on back.
|
L0110XA - Headlight assembly, new manufactured, H4 7" with Carello looking glass but with no script or numbers on lens, three perch mount.
|
License plate light assembly perch, chromed metal, allows light to sit at proper angle on bumper
|
License plate light assembly, new manufacture, nicer than original, Carello, slit in glass shroud style, globe shape, correct script
|
License plate light assembly, NOS, Altissimo
|
License plate light assembly, NOS, nicer than original, Carello or Altissimo, slit in glass shroud style, globe shape, correct script, with round gasket
|
Light for dash, blue, brass barrel behind dash, small smooth dome style lens with 11.2mm external knurling, requires 7mm hole in dash, single wire
|
Light for dash, green, brass barrel behind dash, small smooth dome style lens with 11.2mm external knurling, requires 7mm hole in dash, single wire
|
Light for dash, red, brass barrel behind dash, small smooth dome style lens with 11.2mm external knurling, requires 7mm hole in dash, single wire
|
Light for dash, white, brass barrel behind dash, small smooth dome style lens with 11.2mm external knurling, requires 7mm hole in dash, single wire
|
Light for dash, yellow, brass barrel behind dash, small smooth dome style lens with 11.2mm external knurling, requires 7mm hole in dash, single wire
|
Light socket only, to repair or restore taillights and front/rear turn signal assemblies, single contact style
|
Reflector pod gaskets, new manufacture
|
Reflector pod housing, NOS, paint to body color
|
|
|