|
|
Engine Compartment
Cylinder head, twin plug, new manufacture from Italy of original vintage style, with unleaded fuel valve seats and valve guides. Intake bore is for 1600 GTA, can be machined for GTA Jr. or to your specifications. Specify style of valve guide desired an
|
Cylinder head, twin plug, new manufacture from Italy of original vintage style, without valve guides or valve seats, with intake bore unmachined so you can custom fit.
|
Cylinder head, twin plug, prepared for 1600 motor by Jack Beck for racing; valve seats, guides, special valves, special springs installed. Head run in on dyno. Pressure tested and ready to run.
|
Differential limited-slip assembly, complete, new manufacture, specify coarse or fine spline shafts and diameter at spline end, more robust than 2000 c.c. version, designed to fit 1300, 1600, 1750 and 2000 c.c. differential housing.
|
Differential support bushings, verify dimensions to check fit.
|
Distributor points, Marelli, some cars require one set, some require two.
|
Driveshaft center support rubber, D shaped.
|
Engine gasket set, very high quality, asbestos-free modern, high-tech materials. Silk-screened sealant pre-applied to the large gaskets - 1600 only.
|
Engine gasket set, very high quality, asbestos-free modern, high-tech materials. Silk-screened sealant pre-applied to the large gaskets - 1750 only.
|
Engine, Twin-spark, 2000 cc, good used motor from a running car in Italy, includes the F.I. airflow meter, alternator, and starter.
|
Exhaust pipe and muffler, extra heavy duty, great fit, front section that hooks to the headers, the 1st muffler and a pipe out the back. For Giulia Super up to 1970, GT/GTV up to 1970, Duetto Round Tail 1600 only.
|
Exhaust pipes and muffler, front section, 1750 only.
|
Fan blade, high performance, Euro style, requires less HP to turn, 6 blade, white plastic
|
Firewall grommet, heater hose.
|
Fuel filter assembly/Fuel pressure regulator, glass bowl version, NOS, FISPA, specify if uses banjo fittings, or hoses with hose clamps.
|
Fuel filter assembly/Fuel pressure regulator, glass bowl version, NOS, Tecnocar, specify if uses banjo fittings, or hoses with hose clamps.
|
Fuel filter element with new spring, twin carb models
|
Fuse box, NOS, specify style with or without rivets holding ID plate
|
Gas tank sending unit gasket, fits Marelli, Veglia and Jaeger gas tank sending units with six screw mount, this is gasket only.
|
Gas tank sending unit, NOS, specify Veglia or Jaeger, 390722, must match the marker on gauge, specify length of tube from mount flange to tip. This style draws gas from a tube exiting the sending unit/float.
|
Gas tank sending unit, OEM, specify Veglia or Jaeger, must match the gauge, specify the length of tube from mount flange to tip, modern manufacture
|
Ground strap for battery, original wire style, covered with black sleeve, lead terminal end
|
Hand brake cable, Includes front section that attaches to hand brake handle with correct fittings on each end. Also the rear section that connects to each brake.
|
Heater valve diaphram for E0264X
|
Heater valve, NOS, style with 2 small perches for mounting, rebuildable housing, replaceable seal with 4 screws on outside
|
Hose clamp for fresh air hose, or carb plenum to air filter, 2 pieces, includes pre-formed strap and spring clasp, for round or oval hose 3 diameter or larger
|
Hose for air filter, oval, black, new manufacture
|
Hose for air filter, oval, bronze color, NOS
|
Hose, cowl drain. Light grey plastic hose with visible wire winding. Say that three times fast. Just like the original.
|
Muffler hanger, large, stock, rubber about 1 thick\n
|
|
|