|
|
Engine Compartment
Accelerator linkage at firewall rebuild kit, includes 2 firewall rod rubber bushing, 1 steel/rubber bushing for engine compartment actuator rod, and 1 ball end bolt, twin carburetor models only
|
Accelerator linkage bolt with ball on one end.
|
Accelerator rod from firewall to bell crank. For carburetored cars only.
|
Air filter canister, single carb. models, Giulietta Sprint and Spider Normale 1300 only, specify car and chassis number as there were four versions. New manufacture from Italy, quite accurate, very nicely done.
|
Air filter element, for twin carb 1300 Veloce cars.
|
Air filter, NOS, specify dimensions, several are correct for this car
|
Air intake hose rubber base ring, installs at the firewall on the metal tube that holds air intake hose, two per car.
|
Air intake hose, 25" length, large diameter for heater, fresh air, and/or air filter. Heavy duty canvas, wire wound on rubber, finished ends.
|
Air intake hose, 32" length, large diameter for heater, fresh air, and/or air filter. Heavy duty canvas, wire wound on rubber, finished ends.
|
Air intake hose, 44" length, large diameter for heater, fresh air, and/or air filter. Heavy duty canvas, wire wound on rubber, finished ends.
|
Airbox rubber bellows, new manufacture, for firewall mounted style, Veloce only
|
Ball joint boots, lower, large size
|
Ball joint boots, upper, medium size
|
Ball joint kit, lower. Includes both lower ball joints, matching seats, snap rings, and everything else for installation. Fits both sides of car. Specify diameter of ball.
|
Ball joint kit, upper. Includes both upper ball joints and matching seats. This kit includes springs and clips to use in the rebuild of the ball joints. This kit will do both sides of the car
|
Ball joint race, lower or upper, NOS. Specify outside diameter and diameter of the hole in the middle
|
Ball joint, differential, for mounting to trunion bar, very high quality new manufacture, includes 2 hardened seats
|
Ball joints, lower, very high quality new manufacture, includes 2 hardened seats, specify diameter of ball and diameter of the threaded portion of the shaft.
|
Ball joints, upper, very high quality new manufacture, includes 2 hardened seats, specify diameter of ball and diameter of the threaded portion of the shaft.
|
Boot for 5mm spark plug cable connection to distributor caps
|
Boot for 5mm spark plug cable to spark plug connectors.
|
Brake hose kit, racing style, for all Giulietta based cars. Includes two front hoses and one rear hose.
|
Brake hose, front, original style, new manufacture, #1365.64.019, for all Giulietta Spider, and for Giulietta Sprint only after chassis number 0200 (before this number E0141X was used), also valid for 2600 Touring Spider. 3/8 X 24, length of threaded por
|
Brake hose, rear, from body to differential, #1365.64.020 for Giulietta-based cars, also clutch hose for 2600 Touring. 3/8 X 24, long threaded portion is 29/32, short threaded portion is 7/16, overall length is 14 15/16. Verify these dimensions please.
|
Brake lining. NOS. Front or rear, 4 pieces per set. Specify length and width and spacing between rivets to verify fit. These are the original ones, not a re-manufacture
|
Brake reservoir, NOS, Girling, specify diameter, there were 2 choices.
|
Brake return springs, describe style as there are two types used, specify front or rear, NOS.
|
Brake wheel cylinder repair kit, front, style with 3 shoes per wheel, kit does both front wheels, kit does 6 brake cylinders.
|
Brake wheel cylinder repair kit, front, style with two shoes per wheel, new manufacture, kit does both front wheels (4 cylinders)
|
Brake wheel cylinder repair kit, rear, specify if drum or disc brakes on front, kit includes 2 dust boots and 2 seals, and does both rear wheels. For drum brake cars only.
|
|
|